If you listen to InSinkErator you will end up purchasing a new unit if not under warranty. The unit is easily fixed see below my instructions. I did pass this on to thier Customer Service hopefully they will review it and publish the instructions for everyone. It takes no parts just minor disassembling and cleaning.You can easily repair the faucet handle sticking problem from the top. 1.) turn off water – actually you could leave on 2.) using a 3/4 inch open end wrench to remove small retaining cap holding handles in faucet. If you look close you will notice flat sections on cap. Be carefull not to mar finish. 3.) Then pop off handle pivot cap with a small flat screwdriver exposing the stuck plunger. There is hex cap that hold plunger assembly in but you would need a very thin wall socket to remove entire plunger assembly. 4.) Clean as much green goo from plunger area with paper towels and a tooth-pic. 5.
We have owned this product for just over three years and had been happy with the dispenser until recently. Repair parts are not available. Even something as simple as a leaky fitting means that you have to buy a whole new assembly.We had such a leaky fitting and had to replace the entire tank assembly. Fortunately, this happened while still under warranty. More recently, the spacer under the cold water lever wore to the point that it would no longer stay in the detent. The spacer is not available, nor is the cold water cartridge. Our only option is to replace the entire faucet assembly at a cost of $285 (price quoted from the mfgr’s parts dept.).My recommendation is to look for a unit that has repair parts available, either from the manufacturer or aftermarket.
The InSinkErator Indulge Contemporary F-HC1100 Instant Hot Water Dispenser provides filtered near-boiling water and cool drinking water, all in one system. Designed for use with the InSinkErator Stainless Steel Tank (SST-FLTR) and Chilled Water Tank (CWT-00) (both sold separately), this dispenser has a cool-water lever that provides filtered drinking water and a hot-water lever that dispenses filtered near-boiling water for a variety of uses.
|
||||
 |
 200°F water at your fingertips |
 For use with the InSinkErator 2/3-gallon stainless steel tank and filtration system (sold separately). |
 View larger. |
Convenience and Luxury in Your Kitchen
Sleek, Elegant, and engaging, the Indulge Contemporary is the instant hot water dispenser all others envy. Featuring durable all-brass faucet construction, the InSinkErator Contemporary F-HC1100 Instant Hot Water Dispenser is available in 11 designer finishes to complement your kitchen decor. Its graceful high-arching spout swivels for convenience, an especially useful feature for filling larger pitchers and pots. As an added benefit, the Hot lever automatically shuts off, while the Stay-On cool lever remains on for easy use and hands-free operation.
Hundreds of Uses In Your Home
Consider how often you heat water in the kitchen. When you do, you’ll realize just how useful an instant hot water dispenser can be in your kitchen. With 200-degree-Fahrenheit, near-boiling water available at your fingertips, you’ll get more done in less time. Instead of waiting for water to heat, you can finish countless kitchen tasks in seconds and relax or get back to your guests.
An InSinkErator hot water dispenser does more than provide filtered hot water for preparing instant foods and beverages, it is also an incredible kitchen appliance. Use it to loosen stubborn jar lids, prepare pasta, warm baby food, clean crusty pans, cream butter, melt chocolate, remove fruit skins for pies, clean cheese graters, warm ice cream scoops, and warm pancake syrup. These are just a few examples of the many uses of an instant hot water dispenser.
Hot Water Instantly, How Does That Work?
When you activate the hot-water lever on your InSinkErator Instant Hot Water Dispenser, water comes up from the supply line from our specially designed filtration system, guaranteeing you the freshest water possible. From there it travels from the system to our 2/3 gallon tank, where it’s heated to 200 degrees Fahrenheit. As the water is used, it is replaced with more freshly filtered water. With the fast-recovery system, it can deliver up to 60 cups of near-boiling water an hour.
When you activate the cool-water lever, cool tap water travels directly from the filtration system to the faucet. Just pull the hot or cool lever to dispense the water you want. The InSinkErator Chilled Water Tank (CWT-OO) may also be used with the Indulge and Involve Series hot/cool instant hot water dispensers to deliver 38-degree-Fahrenheit chilled drinking water in addition to the near-boiling hot water the dispenser and SST-FLTR provide.
Easy to Install
The InSinkErator Contemporary F-HC1100 Instant Hot Water Dispenser will save you time and effort in the kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why millions of people are now using an InSinkErator Instant Hot Water Dispenser. By following the step-by-step instructions, you’ll soon be enjoying the convenience of instant hot water.
Heating water with the SST-FLTR consumes less energy than a 40-watt light bulb that’s left on for 24 hours and costs just pennies a day to operate. And because hot water is dispensed on demand, you only use the amount of water you need. This helps reduce water waste.
We Come To You Parts and Labor Warranty
The F-HC1100 is backed by an exclusive five-year We Come to You In-Home Service Warranty. If you ever have a problem with your instant hot water dispenser system, an authorized InSinkErator service representative will come to your home and fix or replace it, at no charge to you.
Note: Using other manufacturers’ components with InSinkErator faucets or tanks voids all InSinkErator warranties.
What’s in the Box
InSinkErator Indulge Contemporary F-HC1100 Instant Hot Water Dispenser, hex nut, hex tool, rubber O-ring, and semi-circular mounting plate (SST-FLTR sold separately.)
If you listen to InSinkErator you will end up purchasing a new unit if not under warranty. The unit is easily fixed see below my instructions. I did pass this on to thier Customer Service hopefully they will review it and publish the instructions for everyone. It takes no parts just minor disassembling and cleaning.You can easily repair the faucet handle sticking problem from the top. 1.) turn off water – actually you could leave on 2.) using a 3/4 inch open end wrench to remove small retaining cap holding handles in faucet. If you look close you will notice flat sections on cap. Be carefull not to mar finish. 3.) Then pop off handle pivot cap with a small flat screwdriver exposing the stuck plunger. There is hex cap that hold plunger assembly in but you would need a very thin wall socket to remove entire plunger assembly. The Battle of Clavigo (fresco) by.. – Tea Towel 100% Cotton – Art247 – Tea Towel – 46x70cm Low price . 4.) Clean as much green goo from plunger area with paper towels and a tooth-pic. 5.
We have owned this product for just over three years and had been happy with the dispenser until recently. Repair parts are not available. Even something as simple as a leaky fitting means that you have to buy a whole new assembly.We had such a leaky fitting and had to replace the entire tank assembly. Fortunately, this happened while still under warranty. More recently, the spacer under the cold water lever wore to the point that it would no longer stay in the detent. The spacer is not available, nor is the cold water cartridge. Our only option is to replace the entire faucet assembly at a cost of $285 (price quoted from the mfgr’s parts dept.).My recommendation is to look for a unit that has repair parts available, either from the manufacturer or aftermarket.
questionnairefriedrickcxr 